Skip to Content

Jacket Bag Tutorial.. Recycled Bag

Recycled Bag Tutorial

Create a bag out of a former jacket #tutorial Jacket Bag Tutorial

 

The sleeves are used to make the handles and straps, and the body of the jacket makes the bag.

Before we start some quick tips – your sewing machine is going to be taking some strain stitching through various amounts of bulky fabric. Help it to cope by using the appropriate size sharp needle, using long stitches and sewing slowly.

DSC_0014

  • Start by aligning the jacket, ensuring the bottom of the front and back of the jacket are both straight, and together.
  • Cut across under the arm pit –I recommend using a ruler as a guide to ensure a straight line.

DSC_0016

  • Sew down the front of the jacket, alongside the top stitching. Tip: Remove the buttons, stitch the seam and sew back on.

Straps

  • Next create the handles and top of the bag out of the sleeves. With a little bit of juggling/measuring you can get a top of the bag (the equivalent of a waistband on a skirt), and handle out of each sleeve.
  • Cut the sleeves off from the rest of the jacket along the shoulder seam.

DSC_0021

  • From the longest part of the sleeve cut a 52cm long and 8cm wide piece. This will be folded to create a handle 3cm wide.
  • From the lower part of the sleeve, cut the bag “waistband”. The size will depend on the size of the sleeves, but ideally should be at least 4-5 cm deep, plus seam allowance.    You will either need two pieces per sleeve or to utilise the seam that runs under your arm. This makes the front or back of the “waistband”.
  • When making the handles and “waistband” I recommend using heavy weight interfacing to strengthen the fabric. This part of the bag takes the most strain when used.
  • To make the handles iron on your interfacing press the rectangle in half, then turn in a seam allowance of 1cm along both long edges and press.
  • Top stitch together, on both sides for good visual affect and to add strength.

DSC_0027

  • For the waistband allow 1cm seam allowance and cut the interfacing to the size without seam allowance. This keeps the bulk down, which your sewing machine will appreciate!!

DSC_0035

  • Measure your waistband, unpick the central seam (if utilising the seam in the sleeve) and insert the straps equal distance from the centre. My personal preference is for a 8cm gap between one handle and the next.
  • Re stitch the seam securing the handles.

If you would like a magnetic clasp into the waistband, now is the time to insert it – endeavouring to have the handles equal distance from the sides of the bag, and the clasp in the middle. There are excellent tutorials on-line for inserting a magnetic clasp if you are unsure.

Now you have handles, and the “waist band”.

Body of the bag

  • Compare your waistband size with the top piece of your jacket.
  • These need to match up. You can do this by placing pleats in the jacket, and/or by altering the side seams – this a trial and error process!

DSC_0036

As this bag is made from a larger jacket I am doing both.

  • Stitch in any alterations to match main bag with waistband.
  • Turn the jacket inside out, and sew along the bottom of the jacket. This creates a large pocket/bag.

Lining

DSC_0028

DSC_0033

  • Create any internal pockets you would like.
  • Place the rights sides of you bag lining together and sew round. This creates a bag to match the jacket bag. Note I have not pleated the lining, making it to the size of the main bag, this is to make any internal pockets sit well.
  • Returning to the outside of the jacket bag add some width to the bag by folding the side seam to the bottom seam.

DSC_0014

  • Sew across at a 90 degree angle and sew the same width on the lining.

DSC_0019

  • Trim across.

DSC_0022

  • Hand stitch the lining to the newly created seams, before turning right side out.

DSC_0023

  • With the right sides together pin then tack the waistband to the front of the bag and lining. Do the same for the reverse of the bag. Tip If you are using a magnetic clasp do check it aligns and fastens neatly.
  • Stitch the “waistband” & handles to the body of the bag.

DSC_0008

  • Pin the side seams. Ensure the middle seam of each waistband is correctly aligned with each other.
  • Stitch the side seams of the waistband.

DSC_0013

  • Fold over the waistband, turn in the seam allowance, pin then tack.
  • Top stitch the ”waistband” at the top and bottom.

You’ve done it… excellent   One recycled bag:)

Recycled Bag Tutorial

DSC_0018

Click here to cancel reply.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

PATRICIA

Tuesday 25th of March 2014

I am a beginner in sewing, I look for projects that are not too difficult for me. Besides being new to using a machine, I have disabilities that sometimes makes it difficult for me to understand instructions. I would like to thank you for giving instructions that even I found to be easy to follow. I am so excited about making these bags, I want to run to the thrift stores and buy all the cute jackets so I can make more bags!!!! I would someday love to be good enough to make and sale. This is not only a goal but my dream. Thanks, Patti PORTLAND, OREGON

Amylouise5

Tuesday 25th of March 2014

So pleased you find the instructions easy to follow:) Enjoy making your own versions:)

clementinegoesusa

Sunday 21st of July 2013

cute!

vickymyerscreations

Monday 29th of July 2013

Thank you:)

Sandy

Friday 15th of March 2013

Fabulous! I'll be raiding my closet and the nearby thrift shop to make some of these!

vickymyerscreations

Friday 15th of March 2013

Glad you like the design:)

Jen

Saturday 9th of February 2013

Love it!!

Pam

Saturday 2nd of February 2013

Love how you've kept some of the elements of the jacket in the new bag. A great refashion and well done on your first tutorial.

Pam

Saturday 2nd of February 2013

Hi Vicky, I've featured your Jacket Bag today... Threading Your Way Features

This site uses Akismet to reduce spam. Learn how your comment data is processed.